If you were to set up a VLAN trunk over a Fast Ethernet link on switch R1，
which trunk mode would you set the local port to on R1 if you wanted it to respond to requests from its link partner （R2） and become a trunk？ （）
A. Auto
B. Negotiate
C. Designate
D. No negotiate
您可能感興趣的試卷
你可能感興趣的試題
You are the network administrator at Company and switch R1 is configured as shown below： Interface gigethernet 0/1 Switchport mode trunk
Switchport trunk encapsulation dot1q Switchport trunk native vlan 5
If untagged frames are arriving on interface gigethernet 0/1 of R1，
which of the following statement are correct？（）
A. Untagged frames are automatically assumed to be in VLAN 5.
B. Untagged frames are defaulted to VLAN 1 traffic.
C. Untagged frames are dropped because all packets are tagged when dot1q trunked.
D. Untagged frames are determined on the other switch
E. Untagged frames are not supported on 802.1Q trunks.
If you were to configure an ISL Ethernet trunk between two Cisco switches， named R1 and R2，
what would you have to include at the end of the link for the trunk to operate correctly？ （）
A. An identical VTP mode.
B. An identical speed/duplex.
C. An identical trunk negotiation parameter.
D. An identical trunk encapsulation parameter.
Which of the following technologies would an Internet Service Provider use to support overlapping customer VLAN ID’s over transparent LAN services？ （）
A. 802.1q tunneling
B. ATM
C. SDH
D. IP Over Optical Networking
E. ISL
You need to connect two Company core switches via an ISL trunk.
Which statement is true regarding the configuration of ISL trunks？ （）
A. A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.
B. All Catalyst switches support ISL trunking.
C. A Catalyst switch will report giants if one side is configured for ISL while the other side is not.
D. ISL trunking requires that native VLANs match.
E. None of the other alternatives apply
A new Company switch was just configured using the "switchport trunk native vlan 7" command.
What does this interface command accomplish？（）
A. Causes the interface to apply ISL framing for traffic on VLAN 7
B. Configures the trunking interface to forward traffic from VLAN 7
C. Configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q tagged
D. Configures the trunking interface to send traffic from VLAN 7 untagged
E. None of the other alternatives apply
最新試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which three statements about STP timers are true？（）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）