A new Company switch was just configured using the "switchport trunk native vlan 7" command.
What does this interface command accomplish？（）
A. Causes the interface to apply ISL framing for traffic on VLAN 7
B. Configures the trunking interface to forward traffic from VLAN 7
C. Configures the interface to be a trunking port and causes traffic on VLAN 7 to be 802.1q tagged
D. Configures the trunking interface to send traffic from VLAN 7 untagged
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
You need to configure a new Company switch to support DTP.
Which DTP switchport mode parameter sets the switch port to actively send and respond to DTP negotiation frames？ （）
A. Access
B. No negotiate
C. Trunk
D. Dynamic desirable
E. Dynamic auto
F. None of the other alternatives apply
While using a packet analyzer， you notice four additional bytes being added to the packets in the Company network.
Which protocol inserts a four byte tag into the Ethernet frame and recalculates CRC value？ （）
A. DTP
B. VTP
C. 802.1Q
D. ISL
E. None of the other alternatives apply
You need to configure a new Company switch for trunking.
Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）
A. CompanySwitch（config-if）#switchport trunk encapsulation dot1q
B. CompanySwitch（config-if）#switchport trunk encapsulation itef
C. CompanySwitch（config-if）#switchport trunk encapsulation fddi
D. CompanySwitch（config-if）#switchport trunk encapsulation isl
E. None of the other alternatives apply
Switch R1 has been configured with DTP using the desirable option.
Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）
A. The interface actively attempts to convert the link to a trunk link.
B. The interface is put into permanent trunking mode but prevented from generating DTP frames.
C. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
D. The interface is put into a passive mode， waiting to convert the link to a trunk link.
E. None of the other alternatives apply
The core Company switches are configured to use 802.1Q trunks.
Which three statements are correct with regard to the IEEE 802.1Q standard？（）
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address
最新試題
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which statement is correct about RSTP port roles？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. Which statement is true about the output？（）