You need to configure a new Company switch for trunking.
Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）
A. CompanySwitch（config-if）#switchport trunk encapsulation dot1q
B. CompanySwitch（config-if）#switchport trunk encapsulation itef
C. CompanySwitch（config-if）#switchport trunk encapsulation fddi
D. CompanySwitch（config-if）#switchport trunk encapsulation isl
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
Switch R1 has been configured with DTP using the desirable option.
Which statement describes Dynamic Trunking Protocol （DTP） desirable mode？（）
A. The interface actively attempts to convert the link to a trunk link.
B. The interface is put into permanent trunking mode but prevented from generating DTP frames.
C. The interface is put into permanent trunking mode and negotiates to convert the link into a trunk link.
D. The interface is put into a passive mode， waiting to convert the link to a trunk link.
E. None of the other alternatives apply
The core Company switches are configured to use 802.1Q trunks.
Which three statements are correct with regard to the IEEE 802.1Q standard？（）
A. The IEEE 802.1Q frame format adds a 4 byte field to a Ethernet frame
B. The packet is encapsulated with a 26 byte header and a 4 byte FCS
C. The protocol uses point-to-multipoint connectivity
D. The protocol uses point-to-point connectivity
E. The IEEE 802.1Q frame uses multicast destination of 0x01-00-0c-00-00
F. The IEEE 802.1Q frame retains the original MAC destination address
Refer to the exhibit. On the basis of the output generated by the show commands，
which two statements are true？（）
A. Because it is configured as a trunk interface， interface gigabitethernet 0/1 does not appear in the show vlan output.
B. VLAN 1 will not be encapsulated with an 802.1q header.
C. There are no native VLANs configured on the trunk.
D. VLAN 2 will not be encapsulated with an 802.1q header.
E. All interfaces on the switch have been configured as access ports.
F. Because it has not been assigned to any VLAN， interface gigabitethernet 0/1 does not appear in the show vlan output.
The Company core switches use 802.1Q trunks to connect to each other.
How does 802.1Q trunking keep track of multiple VLANs？ （）
A. It tags the data frame with VLAN information and recalculates the CRC value
B. It encapsulates the data frame with a new header and frame check sequence
C. It modifies the port index of a data frame to indicate the VLAN
D. It adds a new header containing the VLAN ID to the data frame
E. None of the other alternatives apply
Two Company switches are connected via a trunk link. In this network， the original frame is encapsulated and an additional header is added before the frame is carried over a trunk link. At the receiving end， the header is removed and the frame is forwarded to the assigned VLAN.
This describes which technology？（）
A. DISL
B. ISL
C. DTP
D. IEEE 802.1Q
E. MPLS
F. None of the other alternatives apply
最新試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
What two things will occur when an edge port receives a BPDU？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Which statement is true about the output？（）
Which two statements about the various implementations of STP are true？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）