Which of the following can we draw from the given information concerning the class-map "all-traffic"?（）
A. The class-map "all-traffic" will match all traffic with ip precedence 4 and 5
B. The class-map "all-traffic" will match all traffic with dscp 18 or dscp 43
C. The class-map "all-traffic" will match all traffic with ip precedence 0 or 1
D. The class-map "all-traffic" will match all traffic with dscp 18 and dscp 43
您可能感興趣的試卷
你可能感興趣的試題
A. CIS 1# show class-map forward Class map match-all forward ( id 3) Match ip dscp 18
B. CIS1#show access-map block Class map match-all block (id 4) Match ip dscp 43
C. CIS1# show class-map real-time Class map match-all block (id 5) Match ip dscp 16
D. CIS 1# show class-map pass Class map match-all real-time (id 2) Match ip dscp 40
You are an experienced network administrator in an international company. During your working hours, customers complain that they experience intermittent data loss and they intermittently fail to connect to crucial servers. As shown in the following topology, the 802.1Q trunk between DSW111 and ASW1 fails. Though DSW112 is in the service of HSRP group 11, the SVI for VLAN 11 is up on DSW111.
So as to figure out the problem,
which three commands should you issue on DSW111? （）(Choose three.)
A. show standby vlan 11 brief
B. show interfaces vlan 11
C. show spanning-tree vlan 11
D. show interfaces
You are troubleshooting an issue which is causing full-sized packets entering the MPLS cloud be dropped. You have discovered that one of the switches in the MPLS core is not a Cisco switch, but otherwise the MPLS MTU size is set to 1508 bytes on the routers.
Based on this information, which of these may be the reason the packets are being dropped?（）
A. The switch on you MPLS core that was not produced by Cisco does not support oversized packets
B. No switches support oversized packets
C. By definition, the maximum MTU is 1500 bytes
D. As MPLS VPN labeling increases the size of the packet by 8 bytes, the IP MTU should have been changed to 1508
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 destination address
A. Show module
B. Show errdisable detect
C. Show environment
D. Show diagnostic content
最新試題
You are trying to initiate an SSH connection to a remote router and are getting rejected with an error code of 0. Which of these might be the cause of the error?（）
Which of the following allows network administrators to easily apply common services and employ features across Cisco switches, routers, and access points with an intuitive GUI?（）
What are four advantages to using tunnel brokers in an IPv6 transition environment?（）
Which three of these items are IPv6 transition mechanisms? （）(Choose three.)
You are an experienced network administrator in an international corporation. One of your clients asks you to configure a network for a financial trading center which requires multiple high-value transactions.And the transactions are very important to the client. In such a situation, which two of the following are basic and most important requirements concerning the configuration? （）(Choose two.)
Refer to the exhibit. Which two of these events will be the result of issuing the above command? （）(Choose two.)
Which configuration will enable OSPF for IPv6 on FastEthernet 0/0/0?（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?（）
As an experienced network engineer, you are asked to troubleshoot a CIS network outage. During the troubleshooting process, you notice that one of your colleagues connects additional devices to the network with the use of his own switch. With the purpose of improving speed, the switch is attached to both network ports in an office, which leads to bridge loop.Enabling which of the following feature will be able to prevent this problem from happening again?（）