You are troubleshooting a problem with a cisco 7920 wireless ip phone on a standalone wlan. the phone rings but， when you Answer ，the call is dropped.
What may have caused this problem？（）
A.publicly secure packet forwarding is enabled.
B.the minimum data rate is not set to 11 mbps.
C.an address resolution protocol is enabled.
D.the access point is set to the least congested channel.
您可能感興趣的試卷
你可能感興趣的試題
A cisco wcs version 4.0 has been installed on a server with a dual pentium 3.0 ghz processor，4 gb ram，and an 80 gb hard drive. a location appliance has been incorporated into the network and is being monitored by the cisco wcs. there are 3000 devices to be tracked but not all of them are being tracked on the cisco wcs.
What can be done to correct the problem？（）
A.add a new location appliance.
B.add a new cisco wcs server dedicated to the location appliance.
C.add 4 gb of ram to the cisco wcs.
D.add a 120 gb hard drive to the cisco wcs.
You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be a roaming bandwidth issuE. in order to verify what kind of issue it is， you decide to increase the bandwidth reserved for roaming on the wlan controller to the maximum.
What level do you set the bandwidth to？（）
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the wlse， you are trying to push out a configuration job to a standalone access point， but the job does not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect snmp communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of ios firmware in the access point
A.1000
B.1500
C.2000
D.2500
A.16 feet [4.8 meters]
B.24 feet [7.3 meters]
C.8 feet [2.4 meters]
D.40 feet [12.1 meters]
最新試題
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）