A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers.
Which of the following could be used to prevent potential routing loops in this design?（）
A. Using an iBGP mesh inside the Enterprise core
B. Configuring default routes in the Enterprise pointing to both R1 and R2
C. Redistributing BGP routes into the Enterprise IGP
D. Tunneling the packets for the i BGP connection between R1 and R2
您可能感興趣的試卷
你可能感興趣的試題
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1.
Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）
A. The next hop is I2's BGP RID
B. The next hop is I2's IP address used on the R2 - I2 neigh bor relationship
C. The next hop is R2's BGP RID
D. The next hop is R2's IP address used on the R1 - R2 neighbor relationship
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）
R1# show ip bgp 190.1.0.0/16
BGP routing table entry for 190.1.0.0/16, version 121
Paths: (1 available, best #1, table Default - IP - Routing - Table)
Advertised to update - groups:
1
1 2 3 4
1.1.1.1 from 2.2.2.2 (3.3.3.3)
Origin IGP, metric 0, localpref 100, valid, internal, best
A. R1 has a neighbor 1.1.1.1 command configured.
B. R1 has a neighbor 2.2.2.2 command configured.
C. The show ip bgp command lists a line for 190.1.0.0/16 with both a n > and an i on the left.
D. R1 is in ASN 1.
R1 in ASN 1 with loopback1 address 1.1.1.1 needs to be configured with an iBGP connection to R2 with loopback2 IP address 2.2.2.2. The connection should use the loopbacks.
Which o f the following commands is required on R1?（）
A. neighbor 1.1.1.1 remote- as 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 ibgp -multihop 2
E. neighbor 2.2.2.2 ibgp - mode
Router R1 has eBGP connections to I1 and I 2, routers at the same ISP. The company that owns R1 can use public address range 130.1.16.0/20. The following output lists all the IP routes in R1's routing table within this rangE. Which of the following answers would cause R1 to advertise the 130.1.1 6.0/20 prefix to its eBGP peers?（）
R1# show ip route 130.1.16.0 255.255.240.0 longer - prefixes
! lines omitteD...
O 130.1.16.0/24 [110/3] via 10.5.1.1, 00:14:36, FastE thernet0/1
O 130.1.17.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1
O 130.1.18.0/24 [110/3] via 10.5.1.1, 00:14:36, FastEthernet0/1
A. Configure R1 with the network 130.1.16.0 mask 255.255.240.0 command.
B. Configure R1 with the network 130.1.16 .0 mask 255.255.240.0 summaryonly command.
C. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed.
D. Redistribute from OSPF into BGP, filtering so that only routes in the 130.1.16.0/20 range are redistributed, and create a BGP summary for 130.1.16.0/20.
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0