A. Stub
B. Totally stubby
C. NSSA
D. Totally NSSA
您可能感興趣的試卷
你可能感興趣的試題
A. Routers cannot redistribute external routes into the area.
B. Routers should have zero Type 3 LSAs in their LSDBs.
C. Routers should have zero Type 5 LSAs in their LSDBs.
D. Routers should learn default routes from the ABRs attached to the area.
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command.
Which of the following is true about the effects of this configuration command?（）
A. R1 will always create and flood a default route into the OSPF domain.
B. R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.
C. R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.
D. R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
The following output exists on Router R1, a router internal to area 1. What can you d etermine as true from the output of the show ip ospf database summary command?（）
A. The LSA was created by an ABR due to an area range command.
B. The LSA was created by an ASBR due to a summary - address command.
C. If cr eated by an area range command, the best metric for a subordinate subnet on that ABR must have been 11.
D. None of the other answers is correct.
R1, an ABR between backbone area 0 and area 1, has intra - area routes in area 0 for 10.1.1.0/24,10.1.2.0/24, and 10.1.3.0/24. These routes have metrics of 21, 22, and 23, respectively. An engineer then adds the area 0 r ange 10.1.0.0 255.255.0.0 command under the OSPF process of R1.
Which of the following is true?（）
A. R1 loses and then re - establishes neighborships with all neighbors.
B. R1 no longer advertises 10.1.1.0/24 to neighbors into area 1.
C. R1 advertises a 1 0.1.0.0/16 route into area 1 with a metric of 23 (largest metric).
D. R1 advertises a 10.1.0.0/16 route into area 1 with metric of 21 (lowest metric).
Use the same scenario as the previous question, w ith one changE.Instead of the distribute-list prefix question in command configured on R1,R1's OSPF process has an area 1 filter-list prefix question in commandconfigured. Again assuming that the subnets listed in the answers actually exist in area 0.
Which of the following occurs on router R1?（）
R1#sh ip prefix - list
ip prefix - list question: 4 entries
seq 5 deny 10.1.2.0/24 ge 25 le 27
seq 15 deny 10.2.0.0/16 ge 30 le 30
seq 20 permit 0.0.0.0/0 le 32
A. R1 will not create/flood a type 3 LSA for su bnet 10.1.2.0/26 into area 1
B. R1 will not create/flood a Type 3 LSA for subnet 10.1.2.0/24 into area 1
C. R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablE
D. R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE
最新試題
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0