A. incorrect distribute lists have been configured
B. missing ip classless command
C. CEF not enabled
D. no default metric configured for EIGRP
您可能感興趣的試卷
你可能感興趣的試題
If a metric is not specified for routes that are redistributed into OSPF, the defaul t metric that is assigned to the routes is 20, except for redistributed BGP routes.
What is the metric that is assigned to redistributed BGP routes?()
A. 200
B. 0
C. 1
D. 10
Refer to the exhibit. Which interoperability technique implemented on the dual - stack routers would allow connectivity between IPv6 sites across automatic created tunnels using the 2002::/16 prefix? ()
A. Dual Stack
B. NAT - PT
C. 6to4 tunnel
D. GRE tunnel
E. ISATAP tunnel
Refer to the exhibit. EIGRP has been configured on al l routers in the network. The command metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A?()
A. R 4 becomes the successor for Network A and will be placed in the routing table. R2 becomes the feasible successor for Network A
B. R4 becomes the successor for Network A and will be included in the routing table. No feasible successor will be selected a s the advertised distance from R2 is higher than the feasible distance
C. R2 becomes the successor and will be placed in the routing table. R4 becomes the feasible successor for Network A
D. R2 becomes the successor and will be placed in the routing t able. No feasible successor will be selected as the reported distance from R4 is lower than the feasible distance
A. 01 - 00 - 5e - 7f - 00 - 01
B. 01 - 01 - ef - ff - 00 - 01
C. 00 - 00 - 00 - 7f - 00 - 01
D. 10 - 00 - ef - ff - 00 - 01
Refer to the exhibit. Router RTA has been configured as a DHCP server. The two debug commands will generate output on RTA when Ho st A requests an IP address. Which set of DHCPD debug messages is in the correct sequence?()
A.DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to client
B.DH CPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: Sending DHCPACK to client
C.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to client
D.DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client
E.DHCPD: Sending DHCPACK to client DHCPD: DHCPD ISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
F.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
最新試題
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?()R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Which of the following answers lists a multicast IPv6 address?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?()
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
Which of the following features work the same in both RIP- 2 and RIPng?()
Router R1 lists the following output from a show command. Which of the following is true about R1?()R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?()B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18