A. Apply the area 4 stub command to all routers in the area
B. On the ABR, use the area 4 stub command with the no - summary keyword
C. On the ABR, specify a default cost for the area with the area default - cost command
D. On the ABR, use the default - information originate command to inject a default route into area 4
E. Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas
您可能感興趣的試卷
你可能感興趣的試題
Your network has a mixture of Fast Ethernet and Gigabit Ethernet links. What needs t o be done to ensure optimal data routing when using OSPF?（）
A. Nothing. OSPF will determine the most optimal path for routing data by default.
B. Adjust the hello and dead timers for more rapid detection of link failures.
C. Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.
D. Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）
A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast
B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point
C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3
D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. What is the effect of the OSPF configuration on router B?（）
A. All interfaces will be in area 0
B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1
C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2
D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2
OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.
What can you conclude about router A?（）
A. Only the router A loopback interface is parti cipating in the OSPF routing process
B. None of the router A interfaces are participating in the OSPF routing process
C. Router A is using the loopback interface IP address as its OSPF router ID
D. Router A does not have any reachable OSPF neighbors
Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly. What can you conclude from the exhibit and the show running - configuration command output? （）
A. The OSPF areas are not configured correctly.
B. The wildcard masks for the 10.x .x.x networks are incorrect.
C. The 172.16.x.x networks need to be connected to area 0 using virtual links.
D. The 172.16.x.x networks are discontiguous. OSPF is automatically summarizing them to 172.16.0.0/16 and data is being "black holed."
E. There is not enough information to make a determination.
最新試題
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Which of the following answers lists a multicast IPv6 address?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）