Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?（）
A. the serial 1/1 address
B. the serial 2/0 address
C. a randomly generated internal address
D. the configured router - id address
您可能感興趣的試卷
你可能感興趣的試題
A.Interfaces have a default metric of 1.
B.Level 1 is intra - area and level 2 is interarea.
C.Level 1 routing is between an end system (ES) and IS while Level 2 routing is between an IS and IS.
D. Hosts send ISHs while routers send ESHs.
E. IS - IS is an open standard.
F. Metrics depend on interface speed.
Intermediate system to intermediate system (IS - IS), is a protocol used by network devices (routers) to determine the best way to forward datagrams through a packet - switched network, a process called routing. Which three attributes are of the IS - IS routing protocol? （）
A. supports VLSM
B. link - state routing protocol
C. operati on is similar to BGP
D. supports two routing levels within an autonomous system
Refer to the exhibit. Which two statements are true?（）
A. DHCPDISCOVER packets will reach the DHCP server.
B. The router will not forward DHCPDIS COVER packets because it has not been configured to do so.
C. This configuration is applied to interface Fa0/1.
D. DHCPDISCOVER packets will not reach the DHCP server because DHCPDISCOVER packets are broadcasts.
E. DHCPDISCOVER packets will not reach the DHCP server because ports 67 and 68 have not been explicitly allowed by the ip forward - protocol command.
F. This configuration is applied to interface Fa0/0.
A. when all equipment is manufactured by Cisco
B. when there are multiple paths to destination networks
C. because having multiple routing protocols confuses hackers
D. when migrating from an older Interior Gateway Protocol (IGP) to a new IGP
E. when using UNIX host - based routers
F. when smaller broadcast domains are desired
A. The multicast sources must register with the RP to form the multicast distribution tree.
B. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
C. The mu lticast receivers must register with the RP to form the multicast distribution tree.
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
E. An RP is required only in networks running Protocol Independent Mu lticast sparse - dense mode (PIM - SDM).
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
最新試題
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）