A. using aggregate routes
B. defining routes via the network statement
C. disablin g synchronization
D. forcing the next - hop address
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? （）
A. Router A will prefer the path through router B for network 172.20.0.0
B. Router A will prefer the path through router C for network 172.20.0.0
C. Packets from router D will prefer the path through router B for networks advertised by router A
D. Packets from r outer D will prefer the path through router C for networks advertised by router A
A. Advertise with a high MED value all networks that are discovered via external BGP.
B. Set the no - export community attribute on all networks that are advertised externally.
C. Remove the AS - Path information on all routes in the BGP table pr ior to advertising externally.
D. Set the origin code to incomplete for all networks that are discovered via external BGP.
E. Only advertise networks externally if they have been discovered via internal BGP.
F. Use an outgoing distribution list to filte r all networks not originating from inside the autonomous system.
Refer to the exhibit. Network 10.0.0.0/8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0/8 network is true? （）
A. Router R2 will be preferred because it has the higher neighbor IP address.
B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.
C. Router R1 will be preferred because it has a lower local preference.
D. Router R2 will be preferred because it has a higher local preference.
E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.
F. Router R1 will be preferred because it has the lower neighbor IP address.
Refer to the exhibit. Routers RTA and RTB are running BGP but the session is active. What command needs to be added to esta blish the BGP session? （）
A. ip route 10.10.10.1 255.255.255.255 s0/0 ip route 10.10.10.1 255.255.255.255 s0/1
B. network 10.10.10.0
C. no synchronization
D. neighbor 10.10.10.1 next - hop - self
Examine the above configuration. What does the route map named test accomplish?（）
A. permits only the 10.0.0.0/8 prefix to be advertised to the 10.1.1.1 neighbor
B. marks all prefixes received fro m the 10.1.1.1 neighbor with a MED of 200
C. marks the 10.0.0.0/8 prefix advertised to the 10.1.1.1 neighbor with a MED of 200
D. permits only the 10.0.0.0/8 prefix to be received from the 10.1.1.1 neighbor
E. marks all prefixes advertised to the 10.1.1 .1 neighbor with a MED of 200
F. marks the 10.0.0.0/8 prefix received from the 10.1.1.1 neighbor with a MED of 200
最新試題
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1