Refer to the exhibit.
What is the problem with this configuration？（）
A. Spanning tree PortFast cannot be configured on a port where a voice VLAN is configured.
B. Sticky secure MAC addresses cannot be used on a port when a voice VLAN is configured.
C. Spanning tree PortFast cannot be configured on a port when a sticky secure MAC address is used.
D. The switch port must be configured as a trunk.
您可能感興趣的試卷
你可能感興趣的試題
You need to configure port security on switch R1.
Which two statements are true about this technology？ （）
A. Port security can be configured for ports supporting VoIP.
B. With port security configured， four MAC addresses are allowed by default.
C. The network administrator must manually enter the MAC address for each device in order for the switch to allow connectivity.
D. Withsecurity configured， only one MAC addresses is allowed by default.
E. Port security cannot be configured for ports supporting VoIP.
Refer to the exhibit. Based on the running configuration that is shown for interface FastEthernet0/2，
what two conclusions can be deduced？（）
A. Connecting a host with MAC address 0000.0000.4147 will move interface FastEthernet0/2 into error disabled state.
B. The host with address 0000.0000.4141 is removed from the secure address list after 5 seconds of inactivity.
C. The sticky secure MAC addresses are treated as static secure MAC addresses after the running configuration is saved to the startup configuration and the switch is restarted.
D. Interface FastEthernet0/2 is a voice VLAN port.
E. The host with address 0000.0000.000b is removed from the secure address list after 300 seconds.
Refer to the exhibit.
Which interface or interfaces on switch SW_A can have the port security feature enabled？（）
A. Ports 0/1 and 0/2
B. The trunk port 0/22 and the EtherChannel ports
C. Ports 0/1， 0/2 and 0/3
D. Ports 0/1， 0/2， 0/3， the trunk port 0/22 and the EtherChannel ports
E. Port 0/1
F. Ports 0/1， 0/2， 0/3 and the trunk port 0/22
A Company switch was configured as shown below：
switchport mode access switchport port-security
switchport port-security maximum 2
switchport port-security mac-address 0002.0002.0002
switchport port-security violation shutdown
Given the configuration output shown above，
what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port？ （）
A. The host will be allowed to connect.
B. The port will shut down.
C. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
D. The host will be refused access.
E. None of the other alternatives apply
VLAN maps have been configured on switch R1.
Which of the following actions are taken in a VLAN map that does not contain a match clause？ （）
A. Implicit deny feature at end of list.
B. Implicit deny feature at start of list.
C. Implicit forward feature at end of list
D. Implicit forward feature at start of list.
最新試題
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Which two statements are true when the extended system ID feature is enabled？ （）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. Which statement is true about the output？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）