A.Mismatched EtherChannel protocol
B.Mismatched EtherChannel port selection
C.Mismatched EtherChannel distribution algorithm
D.Mismatched trunk mode
E.Mismatched native VLAN
F.Mismatched link speed
您可能感興趣的試卷
你可能感興趣的試題
A.NAT mapping
B.NAT overloading
C.NAT caching
D.Static NAT
E.Dynamic NAT
F.Overlapping NAT
A.The network is load balancing among different members of the VRRP group
B.The default hello timers are 1 second
C.The interface IP address is being used as the virtual IP address
D.There are several routers in the group simultaneously forwarding traffic for the group
E.It is a Cisco Proprietary protocol
F.The default hello timers are 3 seconds
A.A routed port does not run STP or DTP
B.A routed port is considered to be in a down state if it is not operational at both Layer 1 andLayer 2
C.An SVI is considered to be in a down state if it is not operational at both Layer 1 and Layer 2
D.An SVI is considered to be in a down state only when none of the ports in the correspondingVLAN are active
E.An SVI port does not run 5TP or DTP
F.To create a trunk， an SVI can be logically divided into subinterfaces
A.The interface you configured for AutoQoS is set to half-duplex
B.AutoQoS was configured on only one end of the link
C.The interface you configured for AutoQoS has no IP address
D.The interface’s bandwidth is not correctly configured
E.CEF is not enabled on the interface
F.You enabled AutoQoS on the interface but forgot to enable globally first
A.Spanning Tree Protocol
B.Cabling
C.Frame forwarding
D.Packet forwarding
E.EtherChannel
F.Routing protocols
最新試題
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
cisco ios command to interface dialer 0
Which statement correctly describes IPsec VPN backup technology？（）
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Drag and drop each management protocol on the above to the correct category on the below.