A.A routed port does not run STP or DTP
B.A routed port is considered to be in a down state if it is not operational at both Layer 1 andLayer 2
C.An SVI is considered to be in a down state if it is not operational at both Layer 1 and Layer 2
D.An SVI is considered to be in a down state only when none of the ports in the correspondingVLAN are active
E.An SVI port does not run 5TP or DTP
F.To create a trunk， an SVI can be logically divided into subinterfaces
您可能感興趣的試卷
你可能感興趣的試題
A.The interface you configured for AutoQoS is set to half-duplex
B.AutoQoS was configured on only one end of the link
C.The interface you configured for AutoQoS has no IP address
D.The interface’s bandwidth is not correctly configured
E.CEF is not enabled on the interface
F.You enabled AutoQoS on the interface but forgot to enable globally first
A.Spanning Tree Protocol
B.Cabling
C.Frame forwarding
D.Packet forwarding
E.EtherChannel
F.Routing protocols
A.Building schematic
B.IGP community elements
C.Listing of interconnections
D.Physical topology diagram
E.Logical topology diagram
F.Inventory of network equipment
A.An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2
B.The successor route will end up in the routing table， and so will any route with a metric at mostthree times greater than the value of the successor’s metric
C.EIGRP will only advertise routes that are within three hops of the current router
D.The successor route will end up in the routing table， and so will any route with a metric at leastone third the value of the successor’s metric
E.The best three routes with equal cost paths will end up in the routing table
F.The successor route will be any route with three times the value of the advertised distance
A.Several processes can exist simultaneously
B.Requires direct connectivity from the backbone area to all other areas
C.Has the same packet types
D.Can support multiple subnets on a single link
E.Uses a hierarchical structure divided into areas
F.Adjacencies formed with neighbors
最新試題
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）