Refer to the exhibit. Which two problems are the most likely cause of the exhibited output？（）
A.VRRP misconfiguration
B.spanning tree issues
C.transport layer issues
D.physical layer issues
E.HSRP misconfiguration
您可能感興趣的試卷
你可能感興趣的試題
Examine the router output above. Which two items are correct？（）
A.If Ethernet 0/2 goesdown， the standby router will take over
B.The local IP address of Router A is 10.1.0.6
C.When Ethernet 0/3 of RouterA comes back up， the priority will become 105
D.Router A will assume the active state if its priority is the highest
E.The local IP address of Router A is 10.1.0.20
What can be determined about the HSRP relationship from the displayed debug output？（）
A.Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router172.16.11.112
B.The IP address 172.16.11.112 is the virtual HSRP router IP address
C.The nonpreempt feature is enabled on the 172.16.11.112 router
D.The IP address 172.16.11.111 is the virtual HSRP router IP address
E.Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router172.16.11.111
F.The preempt feature is not enabled on the 172.16.11.111 router
Refer to the exhibit. Based upon the debug output that is shown， which three statements aboutHSRP are true？（）
A.The router with IP address 172.16.11.112 is using default HSRP priority
B.The IP address 172.16.11.115 is the virtual HSRP IP address
C.The priority of the router with IP address 172.16.11.112 is preferred over the router with IPaddress 172.16.11.111
D.The router with IP address 172.16.11.111 haspreempt configured
E.The final active router is the router with IP address 172.16.11.111
F.The router with IP address 172.16.11.112 has nonpreempt configured
Refer to the exhibit. Which two statements are true about the output from the show standby vlan50 command？（）
A.The command standby 1 preempt was added to Catalyst_A
B.Catalyst_A is load sharing traffic in VLAN 50
C.Hosts using the default gateway address of 192.168.1.1 will have their traffic sent to192.168.1.11 even after Catalyst_A becomes available again
D.Hosts using the default gateway address of 192.168.1.2 will have their traffic sent toCatalyst_A
A.Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router
B.The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address10.10.0.1
C.The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.1
D.DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2
E.The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address10.0.0.6
最新試題
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
Study the exhibit carefully. The Cisco IOS IPsec High Availability （IPsec HA） Enhancementsfeature provides an infrastructure for reliable and secure networks to provide transparent availability of the VPN gateways - that is， Cisco IOS Software-based routers. What are the twooptions that are used to provide High Availability IPsec？（）
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Identify the recommended steps for worm attack mitigation by dragging and dropping them into thetarget area in the correct order.
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.