A.The Aironet Desktop Utility （ADU ）profile manager feature can create and manage only one profile for the wireless client adapter.
B.The Aironet Desktop Utility (ADU) can support only one wireless client adapter installed and used at a time.
C.The Aironet Desktop Utility (ADU) can be used to establish the association between the client adapter and the access point , manage authentication to the wireless network , and enable encryption.
D.The Aironet Desktop Utility (ADU) and the Microsoft Wireless Configuration Manager can be used at the same time to configure the wireless client adapter.
您可能感興趣的試卷
你可能感興趣的試題
The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting showsand R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
What is the solution of the fault condition？（）
A.Add ipv6 ospf 6 area 0 under S0/0/0/0.23 on R2
B.Add ipv6 ospf 6 area 6 under s0/0/0/0.23 on R2
C.Remove IPv6 address from s0/0/0/0.23 on R2
D.Enable IPv6 routing on s0/0/0/0.23 on R2
The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting shows and R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026：：1：1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026：：1：2/122
ipv6 ospf 6 area 0
Figure 3
The Fault Condition is related to which technology？（）
A.IPv6 Addressing
B.Route Redistribution
C.OSPFv3
D.RIPng
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer. Initial troubleshooting shows that DSW1 can ping the Fa0/1interface of R4 but not the s0/0/0/0.34 interface.
Configurationon DSW1
router eigrp 10
network 10.1.4.4 0.0.0.0
network 10.2.1.1 0.0.0.0
network 10.2.4.13 0.0.0.0
no auto-summary
Configurationon DSW2
router eigrp 10
network 10.1.4.8 0.0.0.0
network 10.2.2.1 0.0.0.0
network 10.2.4.14 0.0.0.0
no auto-summary
Configurationon R4
router eigrp 10
network 10.1.4.5 0.0.0.0
no auto-summary
redistribute ospf 1 metric 100 10 255 1 1500 route-map EIGRP_to_OSPF !
router ospf 1
network 10.1.1.8 0.0.0.0 area 34
redistribute eigrp 10 subnets!
route-map EIGRP→OSPF
match ip address 1!
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 209.0.0.0 0.255.255.255
What is the solution of the fault condition？（）
A.Remove the redistribute command from OSPF process on R4
B.Change the route-map name in the redistribute command under OSPF process to EIGRP→OSPF on R4
C.Change EIGRP AS to 1 on R4
D.Advertise 10.1.1.8/30 network in EIGRP on R4
最新試題
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Drag and drop each function on the above to the hybrid fiber-coaxial architecture component that itdescribes on the below.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
cisco ios command to interface dialer 0