Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement
HSRP has been configurationured between DSW1 and DSW2. DSW1 is configurationured to be activerouter but it never becomes active even though the HSRP communication between DSW1 and DSW2 isworking.
Configuration on DSW1
CertKiller.com
track 1 ip route 10.1.21.128 255.255.0.0 metric threshold threshold metric up 1 down 2!
track 10 ip route 10.2.21.128 255.255.255.0 metric threshold threshold metric up 63 down 64!
interface Vlan10
ip address 10.2.1.1 255.255.255.0
standby 10 ip 10.2.1.254
standby 10 priority 200
standby 10 preempt
standby 10 track 1 decrement 60
Configuration on R4
Cisco 642-832： Practice Exam
interface loopback0
ip address 10.2.21.128 255.255.255.0
What is the solution of fault condition？（）
A.Change standby priority to 140
B.Change standby priority to 260
C.Change standby 10 track 1 decrement 60 to standby 10 track 10 decrement 60
D.Change standby 10 track 1 decrement 60 to standby 10 track 1 decrement 100
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement：
Client 1 is able to ping 10.1.1.2 but not 10.1.1.1. Initial troubleshooting shows that R1 does not have anyOSPF neighbors or any OSPF routes
Configuration on R1：
router ospf 1
CertKiller.com
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12
default-information originate always!
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
Configuration on R2：
router ospf 1
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12!
Cisco 642-832： Practice Exam
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.2 255.255.255.252
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 TSHOOT
What is the solution of the fault condition？（）
A.ipospf authentication message-digestcommand has to be added on S0/0/0/0.12
B.ipospf authentication message-digestcommand has to be added under the OSPF routing process
C.A static route to 10.1.1.4 must be added on R1
D.ipnat outside must be added on S0/0/0/0.12
最新試題
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.
Drag and drop each management protocol on the above to the correct category on the below.
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）